Copper sheets

Rolled copper sheets for electrical and general applications

Supply formats:

Sheet
Flat bar

Medidas: Thicknesses from 0.5 to 100 mm.

Data sheet

Select the different categories of information to generate a personalized PDF file.

Description

At Bronmetal we supply high quality rolled copper for electrical applications and general use.

We supply sheets with thicknesses from 0.5mm to 100mm.

Alloys

Material Designation	Composition in % (m/m)
Cu-ETP	CW004A	max.	99.90^a	–	–	–	–	–	–	Ag, O
min.	–		0,0005	0.040^b	–	0,0005	0,03
Cu-FRHC	CW005A	max.	99.90^a			–	–	–	–	Ag, O
min.	–			0.040^b	–	–	0,04
Cu-OF	CW008A	max.	99.95^a		–	–	–	–	–	Ag
min.	–		0,0005	–^c	–	0,0005	0,03
CuAg0,10	CW013A	max.	Rest	0,08	–	–	–	–	–	Ag, O
min.	–	0,12	0,0005	0.040^b	–	–	0,03
CuAg0,10P	CW016A	max.	Rest	0,08	–	–	0,001	–	–	Ag, P
min.	–	0,12	0,0005	–^c	0,007	–	0,03
CuAg0,10(OF)	CW019A	max.	Rest	0,08	–	–	–	–	–	Ag, O
min.	–	0,12	0,0005	-c	–	–	0,0065
Cu-PHC	CW020A	max.	99.95^a		–	–	0,001	–	–	Ag, P
min.	–		0,0005	–^c	0,006	0,0005	0,03
Cu-HCP	CW021A	max.	99.95^a		–	–	0,002	–	–	Ag, P
min.	–		0,0005	–^c	0,007	0,0005	0,03
Cu-DLP	CW023A	max.	99.90^a		–		0,005	–	–	Ag, Ni, P
min.	–		0,0005		0,013	0,0005	0,03
Cu-DHP	CW024A	max.	99.90^a				0,015	–	–	–
min.	–				0,040	–	–
NOTE – The total of other elements ( different from copper) is defined as the sum of Ag, As, Bi, Cd, Co, Cr, Fe, Mn, Ni, O, P , Pb, S, Sb, Se, Si, Sn, Te and Zn, with the exclusion of any of the elements whose value is indicated individually.
^a including silver (Ag), up to a maximum of 0.015% ^b Up to 0.060% of oxygen content is permitted, subject to an agreement between client and supplier.. ^c Oxygen content must be such that the material complies with the requisites for embrittlement by heating in a hydrogen atmosphere as in Norm En 1976.

Electrical properties

Designations	Volumen Resistivity Ω x mm² m max.	Resistivity mass^a Ω x g m² max.	Conductivity
Cu-ETP Cu-FRHC CU-OF CuAg0,10 CuAg0,10(OF) Cu-PHC	CW004A CW005A CW008A CW013A CW019A CW020A	M	0,01754	0,1559	57,0	98,3
H040	R200	0,01724	0,1533	58,0	100,0
H040	R220
H065	R240	0,01754	0,1559	57,0	98,3
H090	R290
H110	R360	0,01786	0,1588	56,0	96,6
CuAg0,10P Cu-HCP	CW016A CW021A	M	0,01786	0,1588	56,0	96,6
H040	R200	0,01754	0,1559	57,0	98,3
H040	R220
H065	R240	0,01786	0,1588	56,0	96,6
H090	R290
H110	R360	0,01818	0,1616	55,0	94,8
NOTE 1 – The IACS % values are calculated as percentages of the normalized value of high conductivity annealed copper, according to those established by the International Electrotechnical Commission. Copper whose volume resistivity is of 0,017 24 Ω x m, at 20ºC, is defined as that corresponding to a conductivity of 100%.
NOTE 2 – 1 MS/m is equivalent to 1 m/(Ω x mm²).
^a Calculated with a copper density of 8.89 g/cm³ ^b IACS: International Annealed Copper Standard

Equivalences

EN	DIN	ASTM	AFNOR	BS	JIS	SN
Cu-ETP	CW004A	E-Cu58	20065	C11000	CuA1	C101	C1100	Cu-ETP
Cu-OFE	CW009A	–	–	C10100	CuC2	C110	–	Cu-OFE
Cu-OF	CW008A	OF-Cu	2.0040	C10200	CuC1	C103	C1020	Cu-OF
Cu-HCP	CW021A	Se-Cu	2.0070	–	–	–	–	–
Cu-PHC	CW020A	Se-Cu	2.0070	C10300	–	–	–	Cu-HCP
Cu-PHCE	CW022A	–	–	–	–	–	–	–
CuAg0,10	CW013A	CuAg0,10	2.1203	C10700	–	–	–	–
C10940
C11600
CuAg0,04P	CW014A	–	–	C11904	–	–	–	–
CuAg0,10P	CW016A	CuAg0,1P	2.1197	C11907	–	–	–	CuAg0,1P
Cu-DHP	CW024A	SF-Cu	2.0090	C12200	CuB1	C106	C1220	–
C1221
Cu-DLP	CW023A	SW-Cu	2.0076	C12000	CuB2	–	–	Cu-DLP
CuTeP	CW118C	CuTeP	2.1546	C14500	CuTe 1336	C109	–	CuTeP
CuFe2P	CW107C	CuFe2P	2.1310	C19400	–	CW107C	–	–
Cu-S	CW114C	CuSP	2.1498	C14700	Cu-S 1336	C111	–	Cu-S

Technical characteristics

Designations	Nominal thickness t^a	Hardness HV	Tensile Strength R_m	Proof stress of 0.2% R_p0.2	Elongation
Cu-ETP^b Cu-FRCH^b Cu-OF CuAg0.10^b CuAg0,10^b CuAg0,10(OF) Cu-PHC Cu-HCP	CW004A^b CW005A^b CW008A CW013A^b CW016A CW019A CW020A CW021A	M	10	25	Rough Lamination

H040	0,10	5	40	65	–	–	–	–	–	–
R220^b			–	–	220	260	–	(140)	33	42
H040	0,20	10	40	65	–	–	–	–	–	–
R200			–	–	200	250	–	(100)	–	42

H065	0,10	10	65	95	–	–	–	–	–	–
R240			–	–	240	300	180	–	8	15

H090	0,10	10	90	110	–	–	–	–	–	–
R290			–	–	290	360	250	–	4	6

H110	0,10	2	110	–	–	–	–	–	–	–
R360			–	–	360	–	320	–	2	–
NOTE 1 – 1 N/mm² equivalent to 1 Mpa
NOTE 2 – The numbers in brackets are not requisites for this norm, they are given only for informative purposes.
^a For thicknesses inferior to 0.10 mm, mechanical properties must be agreed on between client and supplier.
^b For Cu-ETP (CW004A), Cu-FRCH (CW005A) and CuAg0.10 (CW013A) with thicknesses included between 0.10 mm up to and including 0.20 mm, the following values must be applied:
R_m min. 200N/mm² and A_{50 mm} min. 28%.

Designations	Nominal thickness	Tensile Strength R_m	Proof stress of 0.2% R_p0.2	Elongation	Hardness HV	Grain size
Cu-ETP Cu-FRTP Cu-OF Cu-DLP Cu-DHP	CW004A CW006A CW008A CW023A CW024A	R200	greather than 5		200	250	(max. 100)	–	42	–	–	–	–

H040			–	–	–	–	–	40	65	–	–
R220	0,2	5	220	260	(max.140)	33	42	–	–	–	–
H040	–	–	–	–	–	40	65	–	–

R240	0,2	15	240	300	(min. 180)	8	16	–	–	–	–
H065	–	–	–	–	–	65	95	–	–

R290	0,2	15	290	360	(min. 250)	4	6	–	–	–	–
H090	–	–	–	–	–	90	110	–	–

R360	0,2	2	360	–	(min. 320)	2	–	–	–	–	–
H110	–	–	–	–	–	110	–	–	–

Tolerances

Nominal thickness	Tolerance on thickness for nominal widths
0.05^a	0,1	± 10%^b	–	–	–	–	–
0,1	0,2	± 0,010	± 0,007	± 0,015	–	–	–
0,2	0,3	± 0,015	± 0,010	± 0,020	± 0,03	± 0,04	–
0,3	0,4	± 0,018	± 0,012	± 0,022	± 0,04	± 0,05	± 0,07
0,4	0,5	± 0,020	± 0,015	± 0,025	± 0,05	± 0,06	± 0,08
0,5	0,8	± 0,025	± 0,018	± 0,030	± 0,06	± 0,07	± 0,09
0,8	1,2	± 0,030	± 0,022	± 0,040	± 0,07	± 0,09	± 0,10
1,2	1,8	± 0,035	± 0,028	± 0,06	± 0,08	± 0,10	± 0,11
1,8	2,5	± 0,045	± 0,035	± 0,07	± 0,09	± 0,11	± 0,13
2,5	3,2	± 0,055	± 0,040	± 0,08	± 0,10	± 0,13	± 0,17
3,2	4,0	–	–	± 0,10	± 0,12	± 0,15	± 0,20
4,0	5,0	–	–	± 0,12	± 0,14	± 0,17	± 0,23
5,0	6,0	–	–	± 0,14	± 0,16	± 0,20	± 0,26
6,0	7,0	–	–	± 0,16	± 0,19	± 0,23	± 0,29
7,0	8,0	–	–	± 0,18	± 0,22	± 0,26	± 0,32
8,0	9,0	–	–	± 0,20	± 0,25	± 0,29	± 0,35
9,0	10,0	–	–	± 0,22	± 0,28	± 0,32	± 0,38
10,0	25,0	–	–	± 0,25	± 0,30	± 0,35	± 0,45
^a Includes value 0.05
^b ± 10% del Nominal thickness

Nominal thickness	Tolerances on thickness, for nominal widths of
–	2,5	By agreement	By agreement	By agreement	By agreement
2,5	5,0	± 0,25	± 0,30	± 0,30	± 0,35	± 0,35	± 0,45
5,0	7,5	± 0,35	± 0,45	± 0,40	± 0,50	± 0,45	± 0,55
7,5	10	± 0,45	± 0,60	± 0,50	± 0,65	± 0,55	± 0,75
10	15	± 0,75	± 0,95	± 0,80	± 1,00	± 0,90	± 1,10
15	25	± 0,95	± 1,20	± 1,05	± 1,30	± 1,30	± 1,60
25	50	± 1,30	± 1,60	± 1,40	± 1,75	± 1,50	± 1,90
50	–	± 1,50	± 1,90	± 1,65	± 2,05	± 1,80	± 2,20
1) For all materials, except CuAl8Fe3 (CW303G), CuNi10Fe1Mn (CW352H), CuNi30Mn1Fe (CW354H) y CuZn20Al2As (CW702R) 2) For all alloys CuAl8Fe3 (CW303G), CuNi10Fe1Mn (CW352H), CuNi30Mn1Fe (CW354H) y CuZn20Al2As (CW702R)

Nominal thickness	Thickness tolerances for nominal widths of ^a
0.1^b	0,2	± 0,018	–	–	–
0,2	0,3	± 0,022	± 0,03	± 0,04	–
0,3	0,4	± 0,025	± 0,04	± 0,05	± 0,07
0,4	0,5	± 0,03	± 0,05	± 0,06	± 0,08
0,5	0,8	± 0,04	± 0,06	± 0,07	± 0,09
0,8	1,2	± 0,05	± 0,07	± 0,09	± 0,10
1,2	1,8	± 0,06	± 0,08	± 0,10	± 0,11
1,8	2,5	± 0,07	± 0,09	± 0,11	± 0,13
2,5	3,2	± 0,08	± 0,10	± 0,13	± 0,17
3,2	4,0	± 0,10	± 0,12	± 0,15	± 0,20
4,0	5,0	± 0,12	± 0,14	± 0,17	± 0,23
5,0	6,0	± 0,14	± 0,16	± 0,20	± 0,26
6,0	7,0	± 0,16	± 0,19	± 0,23	± 0,29
7,0	8,0	± 0,18	± 0,22	± 0,26	± 0,32
8,0	9,0	± 0,20	± 0,25	± 0,29	± 0,35
9,0	10,0	± 0,22	± 0,28	± 0,32	± 0,38
^a For all alloys CuAl8Fe3 (CW303G), CuNi10Fe1Mn (CW352H), CuNi30Mn1Fe (CW354H) y CuZn20Al2As (CW702R), tolerances on thickness must be multiplied by 1.25 and the result rounded up to 0.01mm ^b includes 0.1. NOTE – For thicknesses greater than 10 mm, tolerances are those indicated in Norm EN 1653.

Select one of the previous options before downloading the personalized file

Custom tab summary

Value Copper 10/10/2022

Previous value 07/10/2022

7.893,84 €/Ton

7.732,31 €/Ton

*Prices Based on the Metals Market of

Documentation download

Title

Other languages

Type

Created

INDUSTRIAL SECTOR Bronmetal

Type Catalogue

Created 02/12/2019

ELECTRICAL SECTOR. Bronmetal

Type Catalogue

Created 02/12/2019

Copper sheets

Supply formats:

Sheet

Flat bar

Description

COPPER SHEETS FOR ELECTRICAL APPLICATIONS

COPPER SHEETS FOR GENERAL PURPOSES

COPPER SHEETS FOR ELECTRICAL APPLICATIONS

COPPER SHEETS FOR GENERAL PURPOSES

TOLERANCES ON THICKNESS OF HOT-ROLLED PRODUCTS

TOLERANCES ON THICKNESS OF COLD ROLLED PRODUCTS

Bimetal strip

Bimetal strip

Bimetal overlay

Bimetal overlay

Copper strips

Copper strips

Flat copper bar / rectangular bar

Flat copper bar / rectangular bar

Contact us

Contact us

Copper sheets

Supply formats:

Sheet

Flat bar

Description

COPPER SHEETS FOR ELECTRICAL APPLICATIONS

COPPER SHEETS FOR GENERAL PURPOSES

COPPER SHEETS FOR ELECTRICAL APPLICATIONS

COPPER SHEETS FOR GENERAL PURPOSES

TOLERANCES ON THICKNESS OF HOT-ROLLED PRODUCTS

TOLERANCES ON THICKNESS OF COLD ROLLED PRODUCTS

Política de Cookies

Contact us

Contact us